Cisco apply config - Revision history

Pio2pio: /* Apply config to a router */

2014-11-05T14:37:01Z

Apply config to a router

← Older revision		Revision as of 16:37, 5 November 2014
Line 60:		Line 60:

	Please visit [[Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone#Basic_router_config \| apply router config]] section.		Please visit [[Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone#Basic_router_config \| apply router config]] section.

			= Check config recent changes before saving =

			switch#'''show archive config differences'''
			!Contextual Config Diffs:
			!No changes were found

			switch#write memory
			Building configuration...
			[OK]

	[[Category:cisco]]		[[Category:cisco]]

Pio2pio: /* Apply config to AP */

2013-12-26T18:43:53Z

Apply config to AP

← Older revision		Revision as of 20:43, 26 December 2013
Line 1:		Line 1:
			= Backup & restore config =
			Please follow this good practice process before applying any device configuration changes.
			;Backup config on <tt>flash:</tt>
			! Save config
			write mem
			! Backup Config
			copy start PRE_CM_11223344.conf
			;Restore config from <tt>flash:</tt>
			config replace flash:PRE_CM_11223344.conf
			Reply 'Y' when prompted
			write mem

	= Apply config to AP =		= Apply config to AP =
	Ensure that BVI1 interface has IP address		Ensure that BVI1 interface has IP address

Pio2pio: /* Apply config to a router */

2013-12-26T18:30:01Z

Apply config to a router

← Older revision		Revision as of 20:30, 26 December 2013
Line 47:		Line 47:
	= Apply config to a router =		= Apply config to a router =

	[[Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone#Basic_router_config]]		Please visit [[Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone#Basic_router_config \| apply router config]] section.

	[[Category:cisco]]		[[Category:cisco]]

Pio2pio: /* Apply config to a router */

2013-11-25T23:20:01Z

Apply config to a router

← Older revision		Revision as of 01:20, 26 November 2013
Line 46:		Line 46:

	= Apply config to a router =		= Apply config to a router =
	~~WIP.....~~

			[[Cisco_1941_with_AIR-SAP_1602E-E-K9_Standalone#Basic_router_config]]

	[[Category:cisco]]		[[Category:cisco]]

Pio2pio: /* Apply config to a router */

2013-11-10T17:40:18Z

Apply config to a router

← Older revision		Revision as of 19:40, 10 November 2013
Line 47:		Line 47:
	= Apply config to a router =		= Apply config to a router =
	WIP.....		WIP.....


			[[Category:cisco]]

Pio2pio: /* Apply config to AP */

2013-10-23T01:07:27Z

Apply config to AP

← Older revision		Revision as of 03:07, 23 October 2013
Line 18:		Line 18:

	2 -rwx 3569 Mar 1 1993 03:07:13 +00:00 config.txt		2 -rwx 3569 Mar 1 1993 03:07:13 +00:00 config.txt
	~~3 -rwx 0 Mar 1 1993 01:53:44 +00:00 air-sap1602e-e-flash.tar~~
	12 drwx 512 Mar 1 1993 01:51:08 +00:00 ap1g2-k9w7-mx.152-2.JB2		12 drwx 512 Mar 1 1993 01:51:08 +00:00 ap1g2-k9w7-mx.152-2.JB2
	4 -rwx 1914 Mar 1 1993 03:07:13 +00:00 private-config		4 -rwx 1914 Mar 1 1993 03:07:13 +00:00 private-config

Pio2pio: /* Apply config to AP */

2013-10-23T01:07:03Z

Apply config to AP

← Older revision		Revision as of 03:07, 23 October 2013
Line 37:		Line 37:

	3851 bytes copied in 0.040 secs (96275 bytes/sec)		3851 bytes copied in 0.040 secs (96275 bytes/sec)

	ap1#reload		ap1#reload

Pio2pio: Created page with "= Apply config to AP = Ensure that BVI1 interface has IP address ap1>sh ip int brief Interface IP-Address OK? Method Status Protocol BV..."

2013-10-23T01:06:31Z

Created page with "= Apply config to AP = Ensure that BVI1 interface has IP address ap1>sh ip int brief Interface IP-Address OK? Method Status Protocol BV..."

New page

= Apply config to AP =
Ensure that BVI1 interface has IP address
ap1>sh ip int brief
Interface IP-Address OK? Method Status Protocol
BVI1 10.0.99.2 YES DHCP up up
Dot11Radio0 unassigned YES NVRAM up up
Dot11Radio0.10 unassigned YES unset up up
Dot11Radio0.20 unassigned YES unset up up
Dot11Radio0.99 unassigned YES unset up up
Dot11Radio1 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES NVRAM up up
GigabitEthernet0.10 unassigned YES unset up up
GigabitEthernet0.20 unassigned YES unset up up
List files on the access point flash:
ap1#sh flash:

Directory of flash:/

2 -rwx 3569 Mar 1 1993 03:07:13 +00:00 config.txt
3 -rwx 0 Mar 1 1993 01:53:44 +00:00 air-sap1602e-e-flash.tar
12 drwx 512 Mar 1 1993 01:51:08 +00:00 ap1g2-k9w7-mx.152-2.JB2
4 -rwx 1914 Mar 1 1993 03:07:13 +00:00 private-config
5 -rwx 1048 Mar 1 1993 03:07:13 +00:00 private-multiple-fs
6 -rwx 148 Mar 1 1993 01:24:12 +00:00 env_vars
Delete start up config be deleting file <tt>flash:config.txt</tt>
ap1#delete flash:config.txt
Delete filename [config.txt]?
Delete flash:/config.txt? [confirm]
Copy new config from TFTP server to <tt>flash:</tt>
ap1#copy tftp: flash:
Address or name of remote host []? 10.0.99.12
Source filename []? config-ap2-v3.txt
Destination filename [config-ap2-v3.txt]? config.txt
Accessing tftp://10.0.99.12/config-ap2-v3.txt...
Loading config-ap2-v3.txt from 10.0.99.12 (via BVI1): !
[OK - 3851 bytes]

3851 bytes copied in 0.040 secs (96275 bytes/sec)
ap1#reload

System configuration has been modified. Save? [yes/no]: no
Proceed with reload? [confirm]
Writing out the event log to flash:/event.log ...

More to come ...

= Apply config to a router =
WIP.....